Home
Plug-in units
Front profile, shielded
- U front panel, Al, front anodised
EMC seal
- The seal is bonded onto the front panels on the right-hand side he seal is bonded onto the front panels on the right-hand sideof the profile
Front panel for IEEE handle, unshielded
- Front profile, AI 2.5 mm, front anodised, rear side yellow chromated
Shielded EMC Frontpanel to IEEE 1101.10 (CompactPCI & VME64x)
- U front panel, front side anodised, rear side pickled
IEL, inject/eject handles to IEEE with 0,1'' offset
- Suitable for installation of microswitches
- With lock mechanism
IET, low profile, inject/eject handle to IEEE 1101.10 with 0,1'' offset
- For Telecom applications
- Suitable for installation of microswitches
- With lock mechanism
Side-by-side kit for handles
- Allows 2,3 or 4 handles to be mounted side by side as one unit
- For IEL handles
Plug-in units type 2 with extraction handle –↵front panel shielded
- Front panel, shielded
- At 6 U the board location can be moved 1 HP to the right by swapping the upper and lower euroboard bracket
Front panel unshielded for plug-in units type 2 with extraction handle
- Front panel for extractor handle in trapezoidal form
Front panel for plug-in units type 2 with extraction handle
- Front panel for plug-in units type 2 with extraction handle, shielded
Plug-in units type 2 with trapezoid handle, shielded, kit
- Front panel shielded
- Handle without extraction function
Plug-in units type 2 with trapezoid handle, unshielded, kit
- Front panel unshielded
- Handle without extraction function
Front panel unshielded
- Front panel unshielded
Handle in trapezoidal form (without extraction function)
- With separate identification plate
- Handle laterally closed
Contact spring for electrostatic discharge (ESD)
- Assembly between the front panel and the diecast euroboard bracket in a plug-in unit
- Discharge to a horizontal rail with a conductive finish(chromated)
- Configuration top and/or bottom
Centre fixing mounting blocks for Multibus<sup>®</sup>II front panels
- For additional fixing of printed circuit boards
Extractor handle in key form 1
- At 6 U the board location can be moved 1 HP to the right by swapping the upper and lower euroboard bracket
- The holder fixes the location of the printed circuit board to the front panel
- Also suitable with SMD applications
Shielding kit, component side, handles without extraction function
- Connector can be installed according to EN 60603: Type B, C, D, F, H, R.
- Keying/coding is not possible with a separate keying/coding peg
Shielding kit, component side, handles without extraction function
- Connector can be installed according to EN 60603: Type B, C, D, F, H, R.
- Keying/coding is not possible with a separate keying/coding peg
Shielding kit, component side, handles with/ kit without extraction function
- Connector can be installed according to EN 60603: Type B, C, D, F, H, R.
- Keying/coding is not possible with a separate keying/coding peg
Plug-in units type 2 with extraction handle –↵front panel shielded
- Front panel unshielded
- At 6 U the board location can be moved 1 HP to the right by swapping the upper and lower Eurobond bracket
Front panel, shielded
- Front panel, shielded
Unshielded EMC front panel to IEEE 1101.10 (CompactPCI & VME64x)
- Front profile, AI 2.5 mm, front anodised, rear side yellow chromated
3 U shielded EMC front panel to IEEE 1101.10 with 0,1'' offset
- U- front panel, Al, front anodised, rear side etched